Contec COM-2(PCI) User Manual Download

Page: 9 / 80

Introduction

COM-2(PCI), COM-4(PCI), COM-8(PCI)

Support software sold separately

< Examples of CONTEC software products for Windows>

- Driver Software Package (Option)

API-PAC(W32)

< Examples of CONTEC software products for Windows 3.1 >

- Driver Software (Option) (supports COM4-(PCI) only)

API-SIO(PC)WIN

Please follow the setup instructions of the User’s manual shipped
with the software products and/or the help files of the package to
setup our interface board(s) to your system.

For details of CONTEC software products, please contact our sales
agencies.

Features

- As the board supports the PCI bus, the I/O address and IRQ

resource settings are set automatically.

- RS-232C compliant serial I/O ports

Board

Number of channels

COM-2(PCI)

COM-4(PCI)

COM-8(PCI)

- Multiple boards can be installed in the same PC.

Maximum number of

installed boards

COM-2(PCI)

COM-4(PCI)

COM-8(PCI)

Board

- The data transfer rate is software-selectable in the range 50 to

230.4Kbps. The data transfer rate for each channel can be set
independently.

Summary of Contents for COM-2(PCI)

















































































Search results

Summary of Contents for COM-2(PCI)

Reviews:

Related manuals for COM-2(PCI)

Brands by name

Popular brands

Contec COM-2(PCI), User Manual

Search results

Summary of Contents for COM-2(PCI)

Reviews:

Related manuals for COM-2(PCI)

Brands by name

Popular brands