Contec COM-2(PCI) User Manual Download | Manualshive

Page: 8 / 80

background image

Introduction

COM-2(PCI), COM-4(PCI), COM-8(PCI)

1

1.

Introduction

Thank you for purchasing this PCI bus RS-232C communications
board.
This PCI bus board is an interface board for serial data transfer with
external devices. The board is installed in one of the PC's PCI bus
slots or in a PCI bus unit. Please read this manual carefully before
implementing in a system (such as developing application programs
or connecting to external devices).
Use of this board requires either driver software from CONTEC or
your own driver software that accesses the I/O address directly.

Support software provided with the board

COM-DRV(W32) ..... Standard COM serial communications

driver software for Windows 2000, NT, Me,
98 and 95

This is the same software as described in API-PAC(W32).
This software enables the board to be used in the same way as the
PC's COM ports (standard COM).
By adding additional boards, ports COM1 to COM256 can be
installed.
This enables serial communications for purposes such as remote
access service (RAS) and uninterruptable power supplies (UPS).
The software supports the standard Win32 API communication
routines.
Visual Basic communications control is supported.

«
...
6
7
8
9
10
...
»

Summary of Contents for COM-2(PCI)

















































































Reviews:

No comments

Related manuals for COM-2(PCI)

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

UP Squared 6000 Edge Computing Kit

Brand: Aaeon Pages: 59

Brand: SIIG Pages: 12

DIRECTOR PRO series

Brand: MF DIGITAL Pages: 79

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brand: Xmart Pages: 8

Brand: Cervoz Pages: 22

Quadro M6000 Sync

Brand: Nvidia Pages: 8

SiliconDrive SSD-P16G(I)-3100

Brand: Silicon Systems Pages: 108

Brand: AC Infinity Pages: 24

Brand: Forcepoint Pages: 2

Diamond Systems DS-MPE-CAN2L

Brand: Fortec Star Pages: 36

Matrix 6H303-48

Brand: Enterasys Pages: 90

Brand: DataExpert Pages: 48

8 Channel Dimmer Module CLX-1DIM8

Brand: Crestron Pages: 1

2000i 6.5-7.1 Service Pack 1

Brand: Rimage Pages: 174

Avigilon HD-NVR4-PRM-128TB

Brand: Motorola solutions Pages: 31

Brand: Huawei Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands