Contec COM-2(PCI) User Manual Download

Page: 36 / 80

Board Setup

COM-2(PCI), COM-4(PCI), COM-8(PCI)

Note to use CONTEC provides driver software
API-SIO(98/PC)NT.

Cannot use COM port whereby it was allotted in
API-SIO(98/PC)NT. When use API-SIO(98/PC)NT after
installation COM-DRV, remove the registration information of the
board installed with the following process.

(1) Start [Explore], and right click on \WINNT\INF folder, and

choose [Search].

(2) Remove [OEM*.INF] indicated after [COM2K_PI] is inputted

to [Contening text:] and [Search Now] is carried out, and
[OEM*.PNF].

(3) Double-click on the [System] option in [Control Panel], Clicks

on [Hardware] property sheet. Open [Device Manager].

(4) Double-Click on the [Multifunction adapters] folder.

(5) An installed board is chosen, and [Uninstall] is carried out

after [Action].

(6) Do the installation of the board by using the medium of

API-PAC(W32) because [Add New Hardware Wizard] starts
after the OS re-start.

However, cannot use a board as which using API-SIO(98/PC)NT as
the standard COM port.

Summary of Contents for COM-2(PCI)

















































































Search results

Summary of Contents for COM-2(PCI)

Reviews:

Related manuals for COM-2(PCI)

Brands by name

Popular brands

Contec COM-2(PCI), User Manual

Search results

Summary of Contents for COM-2(PCI)

Reviews:

Related manuals for COM-2(PCI)

Brands by name

Popular brands