Contec AD16-64(LPCI)LA Page 53 User Manual Download

Page: 53 / 83

4. Functions

AD16-64(LPCI)LA

Repeat

”Repeat” indicates the number of repetitions of sampling to be executed, from when the sampling start

condition is satisfied until the end of sampling, including delayed sampling.

The number of repetitions is set by means of software, for which conversion is repeated. You can set

an infinite number of repetitions, in which case the conversion is terminated by the software abort

command.

Input data items are stored to the memory sequentially. The repetition state can be subject to status
monitoring and application notification.

Clock

The sampling clock controls the sampling frequency. You can select both the internal sampling clock and

external sampling clock.

Internal sampling clock

The clock signal from the on-board clock generator is used.

External sampling clock
The edge of the digital signal input from an external device is used for the sampling clock.

Summary of Contents for AD16-64(LPCI)LA




















































































Search results

Summary of Contents for AD16-64(LPCI)LA

Reviews:

Related manuals for AD16-64(LPCI)LA

Brands by name

Popular brands

Contec AD16-64(LPCI)LA, User Manual

Search results

Summary of Contents for AD16-64(LPCI)LA

Reviews:

Related manuals for AD16-64(LPCI)LA

Brands by name

Popular brands