Contec AD16-64(LPCI)LA Page 49 User Manual Download | Manualshive

Page: 49 / 83

background image

4. Functions

42

AD16-64(LPCI)LA

1. Setting the Conversion Conditions

First, set the conditions for executing analog input.

Resolution

”Resolution” signifies the number of bits used by an analog input device to represent analog signals.

The higher the resolution, the more finely the voltage range is segmented, allowing the device to convert
analog values to digital equivalents more precisely.

A device with a resolution of 12-bit divides the range width into 4096 segments.

When the device covers the range of 0 - 10V, the minimum unit of converted voltages is 10÷4096

≈

2.44mV.

If the device has a resolution of 16-bit, it is 10÷65536

≈

0.153mV instead.

AD16-64(LPCI)LA

: The resolution is 16-bit.

Input Mode

”Input Mode” indicates the method of connecting analog input signals.

The input modes available are single-ended input and differential input.

The single-ended input mode is suitable for the environment in which the potential difference between

the signal source and ground and noise components can be ignored. For the environment in which they

cannot be ignored, the differential input mode is suitable.

The number of channels available in differential input mode is half that in single-ended input mode.
This board uses on-board jumpers to set the input mode.

Channel

”Channel” represents each point of analog input.

For individual channel numbers, see “Using the On-board Connectors” to “Connector Pin Assignment” in

Chapter 3 "External Connection".

You can specify an arbitrary number of points of analog input by setting the channels by means of
software.

«
...
47
48
49
50
51
...
»

Summary of Contents for AD16-64(LPCI)LA




















































































Reviews:

No comments

Related manuals for AD16-64(LPCI)LA

Brand: Hama Pages: 70

Brand: WOXTER Pages: 98

Brand: Magtek Pages: 18

Brand: Vantec Pages: 7

3DForceFX5700-256DE

Brand: Jaton Pages: 47

Brand: Stanley Pages: 48

iCLASS SE RKCLB40E

Brand: HID Pages: 31

Brand: Hama Pages: 28

Brand: NEC Pages: 8

Brand: NEC Pages: 22

Brand: NEC Pages: 34

Brand: NEC Pages: 72

Brand: NEC Pages: 90

Brand: NEC Pages: 99

Brand: NEC Pages: 97

Brand: NEC Pages: 343

PCGear SDC2001/27

Brand: Philips Pages: 24

Brand: Acer NeWeb Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands