Contec AD16-64(LPCI)LA User Manual Download Page 34

Page: 34 / 83

3. External Connection

AD16-64(LPCI)LA

External Connection

This chapter describes the interface connectors on the board and the external I/O circuits.
Check the information available here when connecting an external device.

How to connect the connectors

Connector shape

The optional connector cable (PCB68PS-**P, ADC-68M/96F or PCA68PS-**P) is used to connect the

board to external devices. The cable is used together with a terminal block to connect external devices.

Two sets of cables are required depending on the number of channels used.

* Please refer to chapter 1 for more information on the supported cable and accessories.

Figure 3.1. Interface Connector Shape

CNA

CNB

Interface Connector (CNA, CNB)

- Connector used

HDRA-E68W1LFDT-SL equivalent

[mfd.by HONDA]

- Applicable connector

HDRA-E68MA1 equivalent

[mfd.by HONDA]

Summary of Contents for AD16-64(LPCI)LA




















































































Search results

Summary of Contents for AD16-64(LPCI)LA

Reviews:

Contec AD16-64(LPCI)LA, User Manual, Page: 34 / 83

Search results

Summary of Contents for AD16-64(LPCI)LA

Reviews: