Contec AD16-64(LPCI)LA Page 56 User Manual Download

Page: 56 / 83

4. Functions

AD16-64(LPCI)LA

Delay

Delayed sampling is performed after the sampling stop condition is satisfied.

When a sampling stop condition other than the software abort command is satisfied, the board performs

sampling for the specified number of times of delayed sampling to store input data to memory.

If you set the number of times of delayed sampling to 0, the board stops sampling the moment the
sampling stop condition is satisfied.

Event

”Event” works as a function for reporting the occurrence of a certain board state to the application.

The following events can be used in combination depending on the specifications and purpose of the
application.

”AD conversion start condition satisfied” event

This event occurs when the AD conversion start condition is satisfied. The event is nullified when
the conversion start condition is “software”.

”Repeat end” event
This even occurs whenever a repetition is completed.

”End of device operation” event
This event occurs when the entire operation including repetitions is completed.

”Stored specified sampling times” event

This event occurs when sampling has been performed for the number of times set by software.
This event can only be used in device buffer mode.

Overflow event
This event occurs at an attempt to store input data with the memory full.

Sampling clock error event

This event occurs when conversion stops as an error occurs due to a sampling clock period that is
too short.

AD conversion error event
This event occurs when conversion stops due to an AD conversion error.

2. Starting/Stopping Operation

Sampling is started by the software command.
Once started, sampling can be stopped by the software command at any timing.

Summary of Contents for AD16-64(LPCI)LA




















































































Search results

Summary of Contents for AD16-64(LPCI)LA

Reviews:

Related manuals for AD16-64(LPCI)LA

Brands by name

Popular brands

Contec AD16-64(LPCI)LA, User Manual

Search results

Summary of Contents for AD16-64(LPCI)LA

Reviews:

Related manuals for AD16-64(LPCI)LA

Brands by name

Popular brands