Contec AD16-64(LPCI)LA Page 21 User Manual Download

Page: 21 / 83

2. Setup

AD16-64(LPCI)LA

Step 2 Setting the Hardware

This section describes how to set the board and plug it on your PC.

The board has some switches and jumper to be preset.
Check the on-board switches and jumpers before plugging the board into an expansion slot.

The board can be set up even with the factory defaults untouched. You can change board settings later.

Replacing the Bracket

This board is shipped with a Low Profile size bracket mounted. To plug the board into a standard size
slot, replace the bracket with the bundled standard size bracket. The replacing method is as follows :

Figure 2.1. Replacing the Bracket

Screws

- Remove the screws and replace it

with the Standard size bracket.

Standard size bracket

Low Profile size bracket

Use a standard screwdriver to attach and detach the screws.

Summary of Contents for AD16-64(LPCI)LA




















































































Search results

Summary of Contents for AD16-64(LPCI)LA

Reviews:

Related manuals for AD16-64(LPCI)LA

Brands by name

Popular brands

Contec AD16-64(LPCI)LA, User Manual

Search results

Summary of Contents for AD16-64(LPCI)LA

Reviews:

Related manuals for AD16-64(LPCI)LA

Brands by name

Popular brands