background image

5

5. Safety Information

The guarantee/warranty will expire if damage is incurred resulting from non-compliance with these operating instructions.
We do not assume liability for any consequential damage.

Nor do we assume any liability for damage to property or personal injury caused by improper use or failure to observe the
safety information. In such cases the warranty/guarantee will expire.

• The unauthorized conversion and/or modification of the product is prohibited for safety and approval reasons (CE).

• The product is not a toy. Devices that are operated with mains voltage have no place in the hands of children. Therefore, be

particularly careful when children are present. Operate the product in a way that it is out of reach of children.

• The system only serves to trigger alarms but does not relieve the user from his diligence obligation.

• The GPS functions only serve to monitor property. The customer is personally responsible for compliance with the statutory

requirements for further monitoring.

• Avoid strong mechanical strain on the system components.

• Do not expose the device to any high temperatures, dripping or splashing water, strong vibrations or heavy mechanical stress.

• The product is only suitable for operation in dry, closed rooms. The entire product must not become damp or wet. The USB mains

adapter otherwise poses danger of potentially fatal electric shock!

• The USB mains adapter is constructed pursuant to protection category II. Only a proper mains socket must be used as voltage

source for the USB mains adapter.

• If the USB mains adapter is damaged, do not touch it. Danger to life from electric shock!

First switch off the mains voltage for the mains socket to which the USB mains adapter is connected (switch off the corresponding
circuit breaker or turn out the fuse, then switch off the FI protection switch so that the mains socket is separated from the mains
voltage on all poles).

Then unplug the USB mains adapter from the mains socket. Dispose of the damaged USB mains adapter in an environmentally
compatible way. Do not use it anymore. Replace it with a new USB mains adapter of the same specifications.

• Do not leave packaging material unattended. It may become a dangerous toy for children.

• Handle the product with care; impacts, shock or fall even from low heights will damage it.

• If you are not sure about the correct connection or if there are any questions that are not covered by the operating instructions, do

not hesitate to contact our technical support or another specialist.

6. General Notes on Rechargeable Batteries

• Keep the rechargeable battery out of reach of children.

• Leaking or damaged batteries/rechargeable batteries can cause chemical burns to skin when touched without the use of adequate protective

gloves!

• The rechargeable battery must never be short-circuited or thrown into fire. There is a risk of fire and explosion!

• Never take the battery apart!

•  If the rechargeable battery heats up strongly when charging, interrupt the charging process!

• Never charge the battery unobserved.

• For reasons of safety, only charge the rechargeable battery on a heat-resistant surface.

• If the rechargeable battery shows any deformation, holes or other obvious defects, no longer use the rechargeable battery and do not try to

charge it.

• Dispose of the rechargeable battery environmentally compatibly.

Summary of Contents for GX103+GPS





































Reviews: