Comtech EF Data SMS-7000, Installation And Operation Manual

Page: 122 / 148

Remote Control Operation SMS-7000 Modem Protection Switch
A–6 Rev. 3 Draft
A.3 Configuration Commands/Responses
A.3.1 Backup Modem
Backup
Modem
Address Command:
Response:
Status:
Response:
<add/ADD_Bx_yyy'cr'
>add/ADD_Bx_yyy'cr''lf']
<add/ADD_Bx_'cr'
>add/ADD_Bx_yyy'cr''lf']
Where:
x = 1 or 2 (backup modem number).
yyy = 0 to 255 (backup modem address; 0 places backup
modem out of service).
Backup
Modulator
Active
(Enable) Command:
Response:
Status:
Response:
<add/MA_Bx_yyy'cr'
>add/MA_Bx_yyy'cr''lf']
<add/MA_Bx'cr'
>add/MA_Bx_yyy'cr''lf']
Where:
x = 1 or 2 (backup modem modulator number).
yyy = YES or NO.
Note: Enter command in Manual mode only.
Backup
Demodulator
Active
(Enable) Command:
Response:
Status:
Response:
<add/DA_Bx_yyy'cr'
>add/DA_Bx_yyy'cr''lf']
<add/DA_Bx'cr'
>add/DA_Bx_yyy'cr''lf']
Where:
x = 1 or 2 (backup modem demodulator number).
yyy = YES or NO.
Note: Enter command in Manual mode only.
Switching
Mode
Selection Command:
Response:
Status:
Response:
<add/SM_Bx_yyy'cr'
>add/SM_Bx_yyy'cr''lf']
<add/SM_Bx'cr'
>add/SM_Bx_yyy'cr''lf']
Where:
x = 1 or 2 (backup modem number).
yyy = IND (Independent) or DEP (Dependent).
Note: Enter command in Manual mode only.
Prime
Modem
Assign. Command:
Response:
Command:
Response:
Status:
Response:
<add/PMA_Bx_yyyyyyyy'cr'
>add/PMA_Bx_yyyyyyyy'cr''lf']
or
<add/PMA_Bx_'cr'
>add/PMA_Bx_'cr''lf']
<add/PMA_Bx'cr'
>add/PMA_Bx_yyyyyyyy'cr''lf']
Where:
x = 1 or 2 (backup modem number).
y = prime modems 1 through 8. (Each 'm' digit represents
a prime modem assigned to a backup modem, i.e.,
<add/PMA_B1_1234 would assign prime modems 1
through 4 to backup #1. If the 'm' digit is omitted following
the '_', then all prime modems will be removed from the
backup modem.)
Notes:
1. In a 1:4 configuration, in which one backup modem is
assigned to 4 prime modems, and the other backup
modem is assigned to the other 4 prime modems,
one backup modem switching mode can be
independent and the other dependent.
2. In a 2:8 configuration in which both backup modems
are assigned to the same prime modem, the backup
modem switching modes must both be the same.
3. Enter command in Manual mode only.
Backup
Multiplexer
Unit
Attached Command:
Response:
Status:
Response:
<add/MU_Bx_yyy'cr'
>add/MU_Bx_yyy'cr''lf']
<add/MU_Bx'cr'
>add/MU_Bx_yyy'cr''lf']
Where:
x = 1 or 2 (backup multiplexer number).
yyy = YES or NO.