Comnet CNGE8FX4TX4MS Installation And Operation Manual Download Page 107

Page: 107 / 115

101

802.1x Per Port Configuration

You can configure a 802.1x authentication state for each port. This state provides Disable,

Accept, Reject and Authorize. Use

Space

key to change the state value.



Reject:

the specified port is required to be held in the unauthorized state.



Accept:

the specified port is required to be held in the authorized state.



Authorized:

the specified port is set to the authorized or unauthorized state in

accordance with the outcome of an authentication exchange between the Supplicant

and the authentication server.



Disable:

The specified port is required to be held in the authorized state



Select

802.1x Per Port Setting interface

Summary of Contents for CNGE8FX4TX4MS




















































































































Search results

Summary of Contents for CNGE8FX4TX4MS

Reviews:

Related manuals for CNGE8FX4TX4MS

Brands by name

Popular brands

Comnet CNGE8FX4TX4MS, Installation And Operation Manual

Search results

Summary of Contents for CNGE8FX4TX4MS

Reviews:

Related manuals for CNGE8FX4TX4MS

Brands by name

Popular brands