manualshive.com logo in svg

Comnet CNGE28FX4TX24MSPOE+, Installation And Operation Manual

Share
Download
Comnet CNGE28FX4TX24MSPOE+ Installation And Operation Manual Download Page 5

inS_CnGE28FX4TX_rEv–

08/31/12     PAGE 5

INSTALLATION AND OPERATION MANUAL 

CNGE28FX4TX

Tech SupporT: 1.888.678.9427

Software Features 

 

»

 Supports C-Ring (recovery time < 30ms over 250 units of connection), MSTP/RSTP/STP (IEEE 
802.1s/w/D) for Ethernet Redundancy

 

»

Support Jumbo frame up to 9K Bytes 

 

»

 24 port 10/100/1000BASE-T(X) PSE fully compliant with IEEE802.3at standard, provide up to 30 
Watts per port

 

»

Power supply included

 

»

Supports IP-based bandwidth management

 

»

Supports application-based QoS management

 

»

Supports IP police security function

 

»

Supports DOS/DDOS auto prevention

 

»

IGMP v2/v3 (IGMP snooping support) for filtering multicast traffic

 

»

Supports SNMP v1/v2c/v3, RMON and 802.1Q VLAN Network Management

 

»

Support ACL, 802.1x User Authentication and for security

 

»

Multiple notification for warning of unexpected event

 

»

 Windows utility (eConsole) support centralized management and configurable by Web-based 
interface, Telnet and Console (CLI)

 

»

Support LLDP Protocol

 

»

19-inch rack mountable design

Summary of Contents for CNGE28FX4TX24MSPOE+

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands