Coltene SciCan STATCLAVE G4 Operator'S Manual Download Page 39 | Manualshive

Page: 39 / 64

Coltene SciCan STATCLAVE G4 Operator'S Manual Download Page 39

38

Sound

Button Beep

Turn the beep ON or OFF

Beep Volume

Adjust sound

Instructions

Water Reservoir Filters

Slide show on how to clean the filters

Drying

Solid/Unwrapped 132°C/4 min

Adjust drying time (0 to 60 minutes)

Solid/Wrapped 132°C/4 min

Adjust drying time (0 to 60 minutes)

Hollow/Unwrapped 132°C/4 min

Adjust drying time (0 to 60 minutes)

Hollow/Wrapped 132°C/4 min

Adjust drying time (0 to 60 minutes)

Textiles/Porous 132°C/4 min

Adjust drying time (0 to 60 minutes)

Rubber & Plastic 121°C/20 min

Adjust drying time (0 to 60 minutes)

Online

Online Access

Enter an email to receive notifications.

Privacy

Agree: Your unit will send cycle data
and unit errors to SciCan. It will also
receive automatic software updates to
the user interface.

Disagree: Your unit will NOT send any
cycle information but it will receive
automatic software updates to the
user interface.

Intro

Select ON, then turn the unit OFF
using the power switch. The start-up
screen and connection wizard will
begin when the unit is next powered
ON.

Remote Access

Use to generate a token that can be
sent to a technician who can access
your unit remotely.

Notifications

Enter email addresses (max. 4) to
which unit can send notifications.

Water Filling

Auto / Manual

Select auto when using an external
auto fill system. Default is manual.

Stand-by

Stand-by On/Off

Select high, low or off. Default is high.

Stand-by Start

Enter time value. Default is 07:00.

Stand-by End

Enter time value. Default is 20:00

«
...
37
38
39
40
41
...
»

Summary of Contents for SciCan STATCLAVE G4

































































Reviews:

No comments