24
English
3) Press the
+
or
-
button until
PROG
is displayed (program)
4) Press the
enter
button, the display will show the number of the program currently running
PRG.1
(for example program 1)
5) Press the
+
or
-
button until a new program is selected.
Note: the internal memory of the
ProSpot 150 LX
holds up to 9 programs. Program number 1is recorded by
coemar
; programs
2 to 9 are recordable, as described in section 15 “Recording programs to the internal memory of the
ProSpot 150 LX
”.
ProSpot
150 LX
will only allow you to select programs which contain recorded steps; empty programs will not be displayed.
5) Press the
+
or
-
button further and the
ProSpot 150 LX
will display
P.ALL
(all recorded programs played back in sequence) and
P.L.RM
(all recorded programs played back in random order).
6) Press the
enter
button to confirm you selection, the display will flash and return to the original display
P3M.1
with the output
now being the newly selected program.
Erasing a recorded program
1) The display shows
P1.M1
(program 1, scene 1, manual trigger, for example).
2) Press the
enter
button.
3) Press the
+
or
-
button until
PR.RE
is displayed (program reset)
4) Press the
enter
button, the display will show the number of the currently running program
PRG.1
(for example program 1)
5) Press the
+
or
-
button until the number of the program you wish to erase is displayed.
Note: The program recorded as described in section 15 “Recording programs to the internal memory of the
ProSpot 150 LX
”. will
be erased, and program number 1 returns to be the default. Selecting
P.ALL
will erase all recorded programs.
6) Press the
enter
button to confirm your selection, the display will seek confirmation
SURE
(are you sure?) and will flash.
7) Press the
enter
button to confirm your selection and erase the selected program; the display will return to the initial setting
P1M.1
.
13.2 “Slaves”
All projectors which are connected to a “
Master
” unit should be set to “
Slave
”. Connections should be as described in section “
8.3.
Synchronising multiple
ProSpot 150 LX
fixtures without DMX signal
”
“
Slave
” units are recognisable since they have connections made to both XLR sockets in their base, except for the final unit in the
chain which has only one connection to its “
DMX IN
”.socket.
Once this is complete, you may proceed to set up units as “
Slave
”.
1- Set the projector to “
Slave
”
(
SLAV
)
.
When the display shows
-SL-
it confirms that it has recorded the setting as
Slave
and will now respond to the commands from
the
master
unit.
Multiple
ProSpot 150 LX
fixtures can execute internally stored, pre-recorded programs (see section 15 “Recording programs to the
internal memory of the
ProSpot 150 LX
“
with control over step speed and fade times controllable via 6 channels of DMX signal
from a standard DMX console.
Projectors correctly connected together may operate in synchronised mode
To activate this automated function, projectors must be connected together as described in the section entitled ”
Synchronising
multiple
ProSpot 150 LX
fixtures via 6 channels of DMX signal.”
Power up the projector and use the 4 button menu
system and the display panel to set dmx channel and the
REM
(remote) setting:
setting the unit for dmx 512 control and addressing
Set the projector to operate via dmx 512 and select the dmx channel to which you wish it to respond for commands as described
in section 12 “Setting the
ProSpot 150 LX
to operate via dmx 512 signal ”.
If using the
coemar
“manual system 6” controller, set the address to “
A001
”.
14. Setting multiple ProSpot 150 LX fixtures to operate in
synchronised mode using 6 channels of DMX signal
M O D E
mode function
To select the function mode
☞
menu
-–S L-–
☞
enter
- S L-
slave
unit
☞
enter
☞
+
o
–
AOO1
