CLIMAVENETA a-CXW 1102 User And Installation Manual Download Page 18

18

EN

The fundamental data concerning the fan coil and the 

heat exchanger are as follows:

Fan coil and heat exchanger:

•  Maximum heat transfer fluid temperature: max 80°C

•  Minimum cooling fluid temperature: min 5°C

•  Maximum operating pressure: 1000 kPa (10 bars)

•  Power supply a-CXW 230V/1/50-60 Hz

•  Power supply i-CXW 230V/1/50 Hz

•  Power consumption: see the rating plate

The technical data for the valves with thermoelectric 

actuators are as follows:

Valves with thermoelectric actuator:

•  Power supply voltage: 230V~50/60Hz

•  VA rating/protection: 5 VA/IP 44

•  Closing time: 180 secs.

•  Maximum glycol content in the water: 50%

Other technical data

All other important technical data (dimensions, 

weights, connections, noise, etc.) are provided in oth-

er parts of this manual, in the separate technical docu-

mentation or in the technical leaflet.

OPERATING LIMITS

•  Product disposal: comply with the environmental 

regulations in force.

•  Disposal of waste electrical and electronic 

equipment (WEEE) pursuant to European Direc-

tive 2012/19/EU. (Applicable in countries with 

separate waste collection systems)

The symbol placed on the product or in the documen-

tation states that, at the end of its working life, the 

products must not be disposed as normal municipal 

solid waste.

The crossed-out wheelie bin symbol is shown on all 

of the products to remind users of the requirements of 

separate waste disposal.

DISPOSAL

authorisation and instructions from the manufactur-

er.

•  If the heat exchanger tubes are improperly handled, 

the hot heat transfer fluid that may escape can 

cause burns.

•  All panels and covers removed for maintenance or 

repairs must be replaced after the work has been 

completed.

For use:

•  Never place anything through the air intake or sup-

ply grills.

•  In particularly cold climates, drain the water from the 

system if not used for long periods.

GENERAL WARNINGS

Summary of Contents for a-CXW 1102









































































Reviews: