background image

47

© 2008 Directed Electronics. All rights reserved.

 Menu 2 - Convenience

2-1 One time bypass Off (1):

  One time bypass ON. When programmed On 

(2) the unit does not passively arm/lock for one cycle when turning the ignition 

On and Off within 3 seconds. When going through this procedure the siren 

chirps once indicating that One Time Bypass has been activated.

2-2 Nuisance Prevention® Circuitry (NPC) On (1):

 Nuisance Prevention Circu-

ity OFF (2). NPC stops repeated triggering of the same zone. If one zone is 

triggered three times in one hour, that zone is bypassed for one hour, starting 

from the time of the third trigger. During that hour, if the system sees a trigger on 

that zone again, the system resets the one hour timer.

If one hour passes and the zone has not triggered again, the zone is activated 

and can trigger the system again. NPC only monitors sensor inputs, and does 

not bypass the door trigger or the ignition trigger at any time.

If  NPC  is  turned  off,  the  system  responds  to  repeated  triggers  on  the  sensor 

inputs and will do so indefinitely. Some states have laws regulating how many 

times a security system can trigger before it is considered a nuisance and the 

vehicle is towed away.

2-3 Disarm from Valet, 1 pulse (1)

. Disarm from valet, 2-5 pulses (2). The system 

can be programmed to count the number of presses of the valet switch before 

disarming the security system. The factory default setting is one pulse. The unit 

can also be set for two to five pulses. 

2-4 Door trigger error chirp On (1):

 Door trigger error chirp Off (2). This feature 

controls the error chirp that is generated if the system is locked with the door 

trigger active. This is useful in vehicles with a long dome light delay after the 

door is closed. If the system is locked before the dome light turns Off, the system 

generates the door trigger error chirp. If this error chirp notification is not desired, 

use this feature to disable the door open error chirp notification. If the error chirp 

notification is turned Off, no bypass chirp is  generated, even if a door is ac-

cidentally left open.

2-5 Ignition Controlled Dome Light Supervision On (1):

 If turned on, the system  

turns on the dome light for 60 seconds when the ignition is turned off. The op-

Summary of Contents for CLIFFORD 50.7X

































































Reviews: