Clifford CLIFFORD 50.7X Page 25 Installation Manual Download | Manualshive

Page: 25 / 64

background image

25

© 2008 Directed Electronics. All rights reserved.

5

BLUE/WHITE

(-) 200 mA 2ND STATUS/REAR DEFOGGER

This wire supplies a 200mA output as soon as the module begins the remote

start process. The Blue/White wire can also be used to activate the defogger

trigger (latched/pulsed) 10-seconds after the remote start engages. (See the

Feature Descriptions, Menu#3, feature #11 for details about programming this

output).

➢

Remote start auxiliary output, 5-pin

These signals are provided to drive additional optional relays.

1

PINK/WHITE

(-) 200mA FLEX RELAY CONTROL OUTPUT

This wire is programmed as (-) 2nd ignition output from factory and can be pro-

grammed (to drive a relay) as a (-) starter or an accessory output.

2

ORANGE

(-) 200mA ACCESSORY OUTPUT

This wire works like the main accessory wire and can be used (with a relay) to

drive any additional accessory circuits in the vehicle.

3

VIOLET

(-) 200mA STARTER OUTPUT

This wire works like the starter wire and can be used (with a relay) to drive any

additional starter circuits in the vehicle.

4

PINK

(-) 200mA IGNITION 1 OUTPUT

This wire works like the ignition 1 wire and can be used (with a relay) to drive

any additional ignition circuits in the vehicle.

Note:

Wires 1 - 4 on the remote start auxiliary outputs are wired to the (-) triggers

for the onboard remote start relays and are not diode isolated. If connecting

these wires directly to the vehicle you must place a 1-amp diode in line to pre-

vent feedback from the vehicle.

«
...
23
24
25
26
27
...
»

Summary of Contents for CLIFFORD 50.7X

































































Reviews:

No comments

Related manuals for CLIFFORD 50.7X

Brand: Agilent Technologies Pages: 20

OM-5RTBR-0709(0)-DENV

Brand: Daikin Pages: 8

Brand: Basta Boatlifts Pages: 5

Brand: Trust Pages: 39

Brand: Hama Pages: 16

Brand: Faber Pages: 12

Brand: LEGRAND Pages: 4

Magellan MG-REM2

Brand: Paradox Pages: 2

Brand: Noble Skiodo Pages: 3

Brand: Datron Pages: 106

Brand: Symetrix Pages: 12

Brand: Hyundai Pages: 8

Brand: Zte Pages: 28

Brand: Remote Control Systems Pages: 4

Brand: Amewi Pages: 29

Brand: Universal Electronics Pages: 4

Brand: 3DiJoy Corporation Pages: 6

Brand: Schumacher Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands