Clifford CLIFFORD 50.7X Installation Manual Download Page 41

Page: 41 / 64

Feature menus

The default settings are indicated in bold type.

➢

Menu 1 - Security

Item

Feature

Opt. 1

Opt. 2

Opt. 3

Opt.4

Opt. 5+

System Arming
Mode

Active

Passive Arm
w/o lock

Passive
Arm w/
lock

Auto re-arm
w/o lock

Auto
re-arm w/
lock

Panic Mode

Ign Off only

Off

Confirmation
Chirps

On w/Warn
chirps On

On w/Warn
chirps Off

Off w/
Warn
chirps On

Off w/
warn
chirps Off

Siren duration

30 sec.

60 sec.

Ign-controlled
locks

No Ign-
locking

Lock &
Unlock

Lock Only

Unlock
Only

DoorLock Pulses

Single

Double Un-
lock Only

Double
Lock Only

Double
Lock &
Unlock

Door lock output
duration

0.8 sec.

3.5 sec.

0.4 sec.

2nd Unlock

No 2nd
Unlock

2nd unlock
on Ign-
control after
first unlock

2nd unlock
on Ign-
control with
first unlock

Comfort Closure

No Comfort
Closure

Comfort
Closure 1

Comfort
Closure 2

Horn function

Full Alarm
Only

Siren Func-
tion 20 mS

Siren
Function
30 mS

Siren
Function
40 mS

Siren
function
50 mS

Hood Trigger
Type

Normally

Open

Normally
closed

Sensor trigger

Single

Double

Summary of Contents for CLIFFORD 50.7X
































































Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Brands by name

Popular brands

Clifford CLIFFORD 50.7X, Installation Manual

Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Brands by name

Popular brands