Clifford CLIFFORD 50.7X Page 7 Installation Manual Download

Page: 7 / 64

What is included

Remote Control 2 way LCD - (p/n 7752X)

•

Remote Control 1 way companion - (p/n 7652X)

•

The control module

•

Control center with integrated status LED and Valet Override switch (p/n

•

6711T)

Revenger™ Soft Chirp™ six-tone programmable siren

•

A remote start defeat toggle switch

•

Installation points to remember

This product is designed for fuel-injected, automatic transmission, or vehicles

with manual transmissions.

Important:

The default option “Manual Transmission Mode”

is a safety precaution that forces the installer to enable the

Manual Transmission Start (MTS) routine or program the unit

to the “Automatic Transmission” option before the remote start

can be activated for the first time.

The “Automatic Transmission” option should be programmed on to work with

automatic transmissions. When the “Manual Transmission” option is selected a

specific routine is required before exiting the vehicle to enable the MTS mode.

➢

Virtual Tach

Virtual Tach is a new feature for Directed this year. It is the default RPM-sensing

method for the new Responder LC hybrid security/remote start systems. Virtual

Tach gives the installer the performance of a hardwired tach wire, with the

convenience of voltage sensing. It is far superior to any voltage-sense feature

you’ve tried before.

Virtual Tach monitors the cranking voltage of the vehicle using a very fast mi-

crocontroller and an analog-to-digital converter. The microprocessor “saves” the

base voltage as a reference. When Virtual Tach “sees” the slightest uptick in

voltage, indicating that the alternator is charging the battery, the starter motor

shuts off instantly.

Summary of Contents for CLIFFORD 50.7X
































































Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Related manuals for CLIFFORD 50.7X

Brands by name

Popular brands

Clifford CLIFFORD 50.7X, Installation Manual

Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Related manuals for CLIFFORD 50.7X

Brands by name

Popular brands