Clifford CLIFFORD 50.7X Page 28 Installation Manual Download | Manualshive

Page: 28 / 64

background image

28

© 2008 Directed Electronics. All rights reserved.

Plug-in LED and valet/program switch

The LED and valet switch are incorporated into the control center, the LED line

plugs into the white 2-pin port and the Valet switch line plugs into the blue 2-pin

port.

Note:

Onboard LED and valet switch can be substituted with an optional out-

board LED (P/N 8634 for Blue LED and 8633 for red LED) and an outboard

valet switch (P/N 8631).

Bitwriter interface - 3-pin black plug

The black 3-pin port is provided for programming the unit using the Bitwriter

(p/n 998T). When using the Bitwriter, it is possible to configure any and all of

the programmable functions as well as lock the Remote Control and System Fea-

tures Learn Routines so that unauthorized users cannot change the configuration

or program remote controls to the unit.

When the learn routines have previously been programmed using the

Bitwriter, they may have been locked. Before proceeding with repro-

gramming the learn routines, they must be unlocked with the Bitwriter

- this cannot be done manually with the Valet switch.

Note:

Bitwriters require software v2.6. Bitwriters with a date code of 6a or older

require an IC upgrade (p/n 998M). Some Bitwriters with a date code of 6B

do not require the IC upgrade, refer to tech tip # 1112 for more information.

Bitwriter 2 compatible.

Optional sensor port - 4-pin connector

There is a shock sensor built onboard the main unit. This connector is an optional

sensor port to add sensors to the security system. Optional sensors that may be

used are: 508D Doubleguard Proximity Field Disturbance, 509U Ultrasonic

Sensor, 506T Glass Break Sensor, and 507M Digital Tilt Sensor.

This input can also be used for a second 504D Doubleguard Shock Sensor, or

for additional pin and magnetic switches.

«
...
26
27
28
29
30
...
»

Summary of Contents for CLIFFORD 50.7X

































































Reviews:

No comments

Related manuals for CLIFFORD 50.7X

Brand: FAAC Pages: 4

Brand: CORNING Pages: 12

Brand: Niko Pages: 28

Brand: Shaw Pages: 44

Brand: RDL Pages: 2

Brand: Heat Controller Pages: 10

Brand: Subaru Pages: 14

Brand: Xantech Pages: 12

Brand: Eurgle Pages: 31

Brand: Hegel Pages: 2

Brand: Honeywell Pages: 64

Brand: Canon Pages: 3

Brand: Canon Pages: 2

Brand: Pulsar Pages: 2

Brand: Ergosleep Pages: 16

Brand: Vivo Pages: 4

Brand: Strongway Pages: 15

Brand: Wagan Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands