Clifford CLIFFORD 50.7X Installation Manual Download

Page: 34 / 64

Remote control Learn Routine™

The system comes with a 1-way and a 2-way remote control that are already

programmed to the system. The system can store up to 4 different remote control

codes in memory.

The remote uses a Supercode Protocol and requires setup before programming

the system.

➢

Remote Control Programming

2 way programming

Make sure the keypad is unlocked.

Press and hold the

AUX

button on the remote for approximately 8 seconds ,

at 3 seconds ignore the car select indicator and continue to hold. The LC

text displays Main Menu until the

AUX

button is released.

Release the

AUX

button. The LC text displays the remote setup options ta-

ble.

Pressing the

AUX

button steps up one Main Menu option per press and

pressing the

AUX

button steps down one Main Menu option per press.

When the Pair Remote menu option is displayed, press and hold the but-

ton for 1 second. The remote emits 3 short beeps and the LC text displays

Pair.

Now enter the remote control learn routine using the control center (as

described on the following page) and choose the Auto learn standard

configuration function listed on the program grid.

1 way programming:

Hold the

AUX

button on the remote until you hear it emit a long beep.

The transmit LED comes on solid (approximately 8 seconds).

Press and hold the

AUX

button and the amber Transmit LED lights up.

Next enter the remote control learn routine and choose the function for

“auto learn configuration” listed on the program grid.

Note:

You do not need to go through the setup for the other features in the

menu.

Summary of Contents for CLIFFORD 50.7X
































































Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Related manuals for CLIFFORD 50.7X

Brands by name

Popular brands

Clifford CLIFFORD 50.7X, Installation Manual

Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Related manuals for CLIFFORD 50.7X

Brands by name

Popular brands