Clifford CLIFFORD 50.7X Installation Manual Download

Page: 45 / 64

chirps that confirm the arming and disarming of the system, Arm/Disarm chirps

ON, w/Warn Away chirps OFF (2), Arm/disarm chirps OFF, w/ Warn Away

chirps ON (3), Arm/disarm chirps OFF, w/Warn Away chirps OFF (4).

1-4, 30 Second Siren Duration:

It is possible to program the unit to sound

for

30 (1)

or 60 (2) seconds during the triggered sequence. Some states have

laws regulating how long a security system can sound.

When using the Bitwriter®, the siren can be programmed to sound for any

length of time from 1 second to 180 seconds.

1-5 Ignition Locks Off:

(

) When turned Off the system does not lock/unlock

the doors. (2) Lock and Unlock: The doors lock three seconds after the vehicles

doors are closed when the ignition is turned On, and unlock when the ignition

is turned Off. (3) Lock: Locks the doors three seconds after the ignition is turned

On and the vehicles doors are closed. (4) Unlock: Unlocks the doors when the

ignition is turned off.

1-6 Single Pulse Lock/Unlock(1):

The system sends out a single pulse when lock-

ing and unlocking. (2) Double-pulse unlock sends out 2 pulses when unlocking.

(3) Double-pulse lock sends out 2 pulses when locking. (4) Double-pulse lock/

unlock sends out 2 pulses when locking and unlocking.

1-7 0.8 sec. Door Lock Pulse Duration (1):

The default setting is 0.8 second

door lock pulses. Some European vehicles, such as Mercedes-Benz and Audi,

require longer lock and unlock pulses to operate the vacuum pump. Program-

ming the system to provide 3.5 second (2) pulses, accommodates the door

lock interface in these vehicles. (See door lock connections section for wiring

information regarding Type E door locks interfacing. The 0.4 second (3) pulse

is required on some vehicles where the lock wires can also control the windows

and the 0.8 second pulse causes the windows to open/close when locking or

unlocking.

1-8 No 2nd Unlock Output (1):

The second unlock output is defeated at all

times. (2) 2nd unlock On with ignition control, after first unlock turns on the

2nd unlock output and unlocks the passengers doors after the driver’s door is

unlocked with ignition controlled locks. (3) 2nd unlock on with ignition control

with first unlock turns on the 2nd unlock output and unlocks the passengers doors

at the same time the driver door is unlocked with ignition controlled locks.

Summary of Contents for CLIFFORD 50.7X
































































Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Related manuals for CLIFFORD 50.7X

Brands by name

Popular brands

Clifford CLIFFORD 50.7X, Installation Manual

Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Related manuals for CLIFFORD 50.7X

Brands by name

Popular brands