Clifford CLIFFORD 50.7X Page 32 Installation Manual Download

Page: 32 / 64

Access door

(Light Flash Fuse Jumper is under
access door - use needle nose pliers to

change fuse position)

➢

Impact Sensor Adjustment

Make sure the keypad is unlocked and the vehicle is disarmed with no open

zones.

Press and hold the

•

AUX

button on the remote for approximately 8 seconds (at

3 seconds ignore the car select indicator) and continue holding.

The status screen clears and the LCD text displays "main menu". Release the

•

AUX

button and the LCD text changes to the remote setup options table.

Pressing the

•

AUX

button steps up one Main Menu option per press.

Pressing the

•

AUX

button steps down one Main Menu option per press.

When the desired Main Menu option (Sensor Adjust) is displayed on the

•

LCD text press and hold the

AUX

button for 1 second, the remote beeps three

times and the siren will emit one long chirp confirming entry into the sensor

adjust mode.

The LCD text displays the current level setting of the impact sensor.

•

Pressing the

•

AUX

button increases the sensitivity up one level and pressing

the

AUX

button decreases the sensitivity on level.

When the desired level is reached, press

•

AUX

on the remote to lock in the

setting.

Summary of Contents for CLIFFORD 50.7X
































































Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Related manuals for CLIFFORD 50.7X

Brands by name

Popular brands

Clifford CLIFFORD 50.7X, Installation Manual

Search results

Summary of Contents for CLIFFORD 50.7X

Reviews:

Related manuals for CLIFFORD 50.7X

Brands by name

Popular brands