![background image](http://html1.mh-extra.com/html/universal-remote-control/ur-j22tve/ur-j22tve_operating-manual_1058828001.webp)
Universal Remote Control, Inc.
www.universalremote.com
OCE-0004A Rev 03(05/14/02)
Operating Manual
for 2 in 1 Cable TV
Remote Control
UR-J22TVE
This remote control is preprogrammed to
operate CABLE Box. Please program it
for your TV by following the instructions
shown below.
The remote control uses AAA batteries.
Please be sure to match the batteries
with the (+) and (-) markings inside the
battery compartment during installation.
The remote control is preprogrammed to
control VOLUME and MUTE functions
through your TV. To switch VOLUME and
MUTE functions to your Cable Box:
STEP1
Press [CATV] and [MUTE] buttons
simultaneously until red light is on.
STEP2
Press [] button.
STEP3
Press [CATV] button.
To return to the TV’s VOLUME, press [TV]
button.
*Tip:
Red light will blink twice.
Set-up for advanced functions
A. To turn on your TV and Cable at the
same time with CATV button:
STEP1
Press [CATV] and [0] buttons
simultaneously until the red light is on.
STEP2
Press [CH +] button.
Set-up for your Cable Box
The remote control is preprogrammed
to control your cable box. If it does not
work properly, please set-up the right
code by using the three-digit code or
searching method.
If you have a TV with a remote control,
we recommend that you plug its power
cord directly into a wall outlet if
available (your cable installer may
select an alternate setup)
Operation
If red light does not blink when you
press keys the operation is intermittent:
Make sure the batteries are inserted
correctly.
Replace old batteries with two new
AAA batteries. Please do not mix old
batteries with new ones.
Instructions
Batteries
Programming your remote
control
Set-up for your VOLUME
control
Helpful hints
STEP3
Point the remote control toward
the TV and enter the three-digit code
from the code table. If there is more than
one code number assigned to your TV
brand, try one code number at a time
until the TV turns off right after you
entered the number.
Searching Method
Press [CH +] button and hold until the TV
turns off. As soon as the TV turns off,
release [CH+] button.
*Tip :
You can confirm the power off and
on by pressing [MUTE] button.
STEP4
Press [TV] button to store the
three-digit code.
*Tip:
Red light will blink twice.
Three-digit code :
Setup for your cable box
No setup is required. The remote control is
preprogrammed to operate your cable box.
Setup for your TV
Find your TV brand and its three-digit
code on the back of this manual.
If the TV brand is not listed, please use
the Searching Method in
STEP3
.
STEP1
Turn on your TV manually.
*Tip :
If you have RCA TV, don’t turn on
the TV.
STEP2
Press [TV] and [MUTE] buttons
simultaneously until the red light is on.
*Tip:
Red light will blink twice.
The [CATV] button sends out the TV and
CABLE power commands if you press
the [CATV] button.
To return to the original function, press the
[CH-] button in the
STEP2
.
B. Recalling the TV Three-digit code :
STEP1
Press [TV] and [MUTE] buttons
simultaneously until the red light is on.
STEP2
Press [VOLUME -] button.
The red light will blink a number of times
indicating the number of each digit of the
code. Each digit is separated by one
second interval of red light being off.
*Tip:
One blink, three blinks and 10 blinks,
indicates the code number 130.
Install two AAA alkaline
batteries as shown here
Open the battery cover