background image

 

P.O Box 578 Casino, NSW, 2470 Australia 

Phone: International  ++614 2902 9083 

Australia (04) 2902 9083 

Website: 

http://rcs-rc.com

 

E mail:  

[email protected]

 

 

TX-10

 

Digital Proportional R/C

 

  

TABLE OF CONTENTS 

PROVIDED IN INSTRUCTIONS. 

 

Page # 1  Introduction. 

 

Page # 2  Preparing the TX-10.  Binding. 

 

Page # 3  Using TX-10 with a LOW off ESC. 

 

Page # 4  Using TX-10 with a CENTRE off ESC. 

 

Specific instructions for operating an RCS ESC 

are found with the supplied ESC  

       Eg Speed & Direction control. 

       Using Sound Trigger functions. 

       Programming the ESC 

       Trouble shooting etc 

PLEASE NOTE. PDF WIRING INSTRUCTIONS ARE HERE: 

 

http://www.rcs-rc.com/pages/instructions

 

Thank you for purchasing this Microprocessor based 

E

lectronic 

S

peed 

C

ontrol 

(ESC)

 R/C system. 

 

THE TX-10 IS FOR USE WITH RCS OMEGA-3v7 ECS’s THAT USE OPERATING PROGRAM Av1  

FOR 

LOW OFF

 CONTROL.   

 

THE TX-10 HANDPIECE HAS A CENTRE OFF DÉTENTE ON SPEED CONTROLLER KNOB.  

THAT ALSO MAKES THE TX-10 SUITABLE FOR USE WITH MOST CENTRE OFF ESC’s 

INCLUDING  

# VIPER-10 SERIES FOR 

CENTRE OFF

 CONTROL. 

 

INSTRUCTION MANUAL

 

THESE INSTRUCTIONS REFER SPECIFICALLY TO THE TX-10 HANDPIECE (SAME AS THE TX-20+). 

They should be read in conjunction with the RCS ESC you are using. 

PLEASE NOTE: THE PLASTIC HANDPIECE ENCLOSURES MAY DIFFER FROM PICTURES BELOW. 

 

“CENTRE OFF Speed Control 

“LOW OFF” Speed Control 

Battery Replacement 

 

 

 

CENTRE OFF LARGE KNOB WITH 

DÉTENTE FOR 150º CONTROL.  

EITHER SIDE OF NEUTRAL.

SWITCH FOR DIRECTION SETTING. 

300º KNOB FOR LOW OFF CONTROL 

OF SPEED. 

INSERT THE 9 VOLT BATTERY. 

DO NOT ALLOW BATTERY TO GO FLAT 

BY LEAVING THE TX SWITCHED ON.

 

THE TX-10 IS GUARANTEED FOR ONE YEAR. 

 

You will supply a locomotive or trail car, the 14 – 20 volt traction batteries (depending on ESC), a fuse, 

ON-OFF switch and wires where necessary, to connect the ESC to the battery and motor(s). 

Where soldering is necessary, we recommend a low wattage soldering iron and resin core solder. 

 

TO AVOID CONFUSION WITH OTHER OPERATORS, WE SUGGEST YOU MARK THE TX TO SHOW WHICH LOCO IT IS OPERATING. 

 

CAUTION 

 

DO NOT ATTEMPT TO ALTER THE TUNING OF THE RADIO EQUIPMENT. 

DO NOT USE RADIO CONTROL EQUIPMENT IN THUNDERSTORMS. 

CHILDREN UNDER 12:       ADULT SUPERVISION RECOMMENDED DURING USE.

!! 

RCS TX & RX PRODUCTS MUST NOT BE USED FOR CONTROLLING RIDE ON LOCOMOTIVES CAPABLE OF 

CARRYING MEMBERS OF THE GENERAL PUBLIC.

 

Summary of Contents for TX-10

Page 1: ...TIONS REFER SPECIFICALLY TO THE TX 10 HANDPIECE SAME AS THE TX 20 They should be read in conjunction with the RCS ESC you are using PLEASE NOTE THE PLASTIC HANDPIECE ENCLOSURES MAY DIFFER FROM PICTURES BELOW CENTRE OFF Speed Control LOW OFF Speed Control Battery Replacement CENTRE OFF LARGE KNOB WITH DÉTENTE FOR 150º CONTROL EITHER SIDE OF NEUTRAL SWITCH FOR DIRECTION SETTING 300º KNOB FOR LOW OFF...

Page 2: ...s 1 1 AUTO BIND receivers 1 3 below Turn on the loco power RX and wait 20 seconds for the RX to enter bind mode RX LED will flash rapidly OR 1 2 MANUAL BIND Turn the loco RX ON The RX LED will start blinking very rapidly to indicate it is ready to be bound 1 3 AUTO BIND Loco power ON RX and wait 20 seconds for the RX to enter bind mode RX LED will flash rapidly The loco with an OMEGA 3v6 7 ESC wil...

Page 3: ...ut any extra parts needed TROUBLESHOOTING The TX 10 battery will eventually go flat if left switched on If the battery goes flat slowly the internal TX 10 operating program will likely be disrupted USING THE TX 10 WITH A CENTRE OFF ESC The TX 10 is ideal for use with RCS CENTRE OFF ESC s such as the VIPER 10 15 VIPER 10 24 Before you switch the system on make sure the large throttle knob is in neu...

Page 4: ... ESC 1 The direction switch is the same as the Ch 3 elevator stick From neutral push the switch forwards once to set the ESC into forwards direction Like an elevator stick it will spring back to the off position when released 2 From the OFF position twist the large knob to the right clockwise CW to ramp the speed up To change from forwards to reverse firstly twist the large knob fully to the left ...

Reviews: