ClearSpan 104895 Manual Download | Manualshive

Page: 14 / 23

background image

CLEARSPAN

™

CEDAR GREENHOUSES

14

Revision date: 06.16.09

CG72141

CG72138

CG72138

CG72138

Rake Board

CG72138

roof panel

6

FAS13

construction

screws

7 & 8

CG72133

Rake Boards

FAS13

construction

screws

9

Attach the roof panels for the remaining side as desired. For the purpose of these instructions, the

6.

diagrams show the two (2) vented panels attached in the middle of the roof side.

NOTE:

Remember to attach the first panel to the front rake board as described in Step 2

before

fastening to the rafters. See diagram below.

With all roof panel in position and secure, attach the two (2) back rake boards (#CG72133) as described

7.

in Section 8.

With the back rake boards secured into position, secure the back roof panels to the rake boards by

8.

installing three (3) 2-1/2" construction screws (#FAS13) through the side of each rake board and into the
roof panel.

FAS13 screw
locations

4

INSTALL ROOF PANELS (continued)

Locate another double roof panel (#CG72138),

4.

set it into position and attach to the rafters using
2-1/2" construction screws (#FAS13). Screws are
installed through the three (3) roof panel frame
columns and into the underlying rafters.

Continue attaching CG72138 roof panels as

5.

previously described until the side of the roof is
complete.

«
...
12
13
14
15
16
...
»

Summary of Contents for 104895
























Reviews:

No comments

Related manuals for 104895

essential Series

Brand: Gabriel Ash Pages: 40

TITAN Peak 240 4,2

Brand: Dancover Pages: 16

Brand: Bio Green Pages: 33

Brand: Palram Pages: 107

Bella 8'x8'- TwinWall Glazing

Brand: Palram Pages: 120

Brand: Gardebruk Pages: 25

Brand: Gardebruk Pages: 2

42' GROWING DOME SNOWSHED DOORWAY

Brand: Growing Spaces Pages: 12

Brand: Vitavia Pages: 24

Double Door Curved 108

Brand: Halls Pages: 24

Brand: Norfolk Greenhouses Pages: 36

Compact Plus 12,1

Brand: Juliana Pages: 22

Brand: Juliana Pages: 36

Brand: Juliana Pages: 38

CITY GREENHOUSE

Brand: Juliana Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands