manualshive.com logo in svg

ClearSpan 104895, Manual

Share
Download
ClearSpan 104895 Manual Download Page 13

13

CLEARSPAN

™

 CEDAR GREENHOUSES

Revision date: 06.16.09

CG72138

Roof Panel

1

CG72138

Roof Panel

Top edge aligns 
with the center 
of end wall.

View as 
seen from 
the inside.

Rake Board

2

FAS13

construction

screws

CG72138

roof panel

SIDE
VIEW

3

FAS13

screw

locations

Frame length of your 
building may differ 
from what is shown.

9

INSTALL ROOF PANELS

WARNING: 

To prevent damage to the panels and to 

prevent serious personal injury, 

do not attempt to install 

the panels on windy days

.

Roof panels can be installed in different locations depending 
on desired result. For the purpose of these instructions, the 
roof panels are installed with the vented panels on the left 
side of the greenhouse as seen from the front.

IMPORTANT: 

 Consider the direction of the prevailing winds when installing the vented roof panels.  These 

panels should be positioned (if possible) so that the prevailing winds cannot catch and damage the vents 
when open. See diagram in upper-right corner. 

NOTE: Drill and countersink all mounting holes to prevent splitting.

Locate a double roof panel (#CG72138) and set it in position as shown below. 

1.

NOTE:

 The roof panel will be flush with the top of the adjacent rake board.  Additionally, the top edge will 

not extend past the center of the ridge assembly. 

Verify the top edge is aligned with the center as shown and secure to the rake board using three (3)       

2.

2-1/2" construction screws (#FAS13). 

Install screws through the rake board and into the roof panel.

NOTE:

When installed correctly, the open edge of the double roof panel will align with the 

center

 of the 

second inside rafter. Panel should be tight against and secured to the rake board at this time.

Secure the panel by installing 2-1/2" construction screws through the double roof panel frame and into 

3.

the rafters beneath in the locations shown in the bottom right diagram.

Prevailing Winds

Summary of Contents for 104895
























Reviews:

No comments

Brands by name

Popular brands

Load more brands