ClearSpan 104895 Page 8 Manual Download | Manualshive

Page: 8 / 23

background image

CLEARSPAN

™

CEDAR GREENHOUSES

8

Revision date: 06.16.09

4

INSTALL FRONT PANELS

WARNING:

To prevent damage to the panels and to prevent serious personal injury,

do not attempt to

install the panels on windy days

.

Secure front panels (#CG12100 & #CG12101) to the base frame as previously described in Section 2.

1.

Attach front panels to the side panels using three 2-1/2" construction screws (#FAS13) as described in

2.

Section 3.

Drill and countersink all mounting holes.

Attach the front peak panel (#CG12114) as described in Section 2.

3.

NOTE:

Verify that the ridge bracket is to the inside of the greenhouse.

CG12101

CG12114

CG12100

Frame length of your
building may differ
from what is shown.

«
...
6
7
8
9
10
...
»

Summary of Contents for 104895
























Reviews:

No comments

Related manuals for 104895

Begonia 938 52411

Brand: habitat et jardin Pages: 22

Brand: KGT Pages: 6

Brand: GrowSpan Pages: 11

Brand: Vitavia Pages: 26

Brand: Vitavia Pages: 38

Brand: TecTake Pages: 18

BIO PROTECT 130/60

Brand: juwel Pages: 8

Easy-Fix 120/100

Brand: juwel Pages: 12

Brand: Gutta Garden Pages: 40

EVOLUTION FUSION

Brand: Alton Pages: 44

Evolution Eight Series

Brand: Alton Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands