Cisco PA-MC-2T3-EC= Installation And Configuration Manual Download | Manualshive

Page: 95 / 96

background image

5-35

PA-MC-T3-EC Port Adapter Installation and Configuration

OL-10589-02

Chapter 5 Configuring the Channelized Mode

Checking the Configuration

Step 3

Repeat the

ping

command using the IP address of the local serial interface. Using the previous example

where the remote server’s IP address was 10.0.0.10, if the local IP address is 10.0.0.5, then use the
command:

ping 10.0.0.5

If the ping is successful, proceed to Step 4. A failure indicates a configuration problem or a hardware
problem with the PA-MC-T3-EC.

Step 4

Remove the local loop with the

no loopback

command and place the remote server or DSU in network

loopback with the

loopback remote

command.

Note

The

loopback remote

command is only available when the framing is set to c-bit parity. If the framing

is not set to c-bit parity, the remote server will have to be placed into network loopback by someone at
the remote site.

Step 5

Repeat Step 3. If the ping is successful, then the PA-MC-T3-EC and the T3 link to the remote site is
functioning correctly. The problem is probably in the remote DSU or server configuration or hardware.
If the ping fails, then a problem exists for: the T3 link to the remote site, the remote server , the DSU
configuration, or the hardware.

«
...
93
94
95
96
»

Summary of Contents for PA-MC-2T3-EC=

































































































Reviews:

No comments

Related manuals for PA-MC-2T3-EC=

Brand: Keithley Pages: 73

Brand: Targus Pages: 4

Brand: Rosewill Pages: 12

Brand: ASIX Pages: 16

Brand: StarTech.com Pages: 10

Brand: TP-Link Pages: 2

Brand: Alpine Pages: 2

USB 2.0 to VGA Pro

Brand: SIIG Pages: 16

Brand: Sigtronics Pages: 5

Cordless Serial Adapter

Brand: Socket Pages: 49

CompactFlash/SDIO Connection Kit with Bluetooth Wireless Technology

Brand: Socket Pages: 91

Brand: Helo Pages: 41

Brand: Alogic Pages: 2

Brand: piezosystem jena Pages: 16

Brand: Linksys Pages: 2

Brand: Linksys Pages: 31

USB100TX - EtherFast 10/100 USB Network Adapter

Brand: Linksys Pages: 28

Brand: Linksys Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands