Cisco PA-MC-2T3-EC= Installation And Configuration Manual Download | Manualshive

Page: 30 / 96

background image

3-2

PA-MC-T3-EC Port Adapter Installation and Configuration

OL-10589-02

Chapter 3 Removing and Installing Port Adapters

Handling Port Adapters

Handling Port Adapters

Each port adapter circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge
(ESD) damage.

Caution

Always handle the port adapter by the carrier edges and handle; never touch the port adapter components
or connector pins. (See

Figure 3-1

.)

Figure 3-1

Handling a Port Adapter

Online Insertion and Removal

The Cisco 7200 VXR platform supports online insertion and removal (OIR) of port adapters; therefore,
you do not have to power down routers when removing and replacing a PA-MC-T3-EC in Cisco 7200
VXR routers.

Note

As you disengage the module from the router or switch, online insertion and removal (OIR)
administratively shuts down all active interfaces in the module.

It is wise to gracefully shut down the system before removing a port adapter that has active traffic moving
through it. Removing a module while traffic is flowing through the ports can cause system disruption.
Once the module is inserted, the ports can be brought back up.

Note

After removing a PA-MC-T3-EC, wait 3 minutes before reinstalling or reinserting a PA-MC-T3-EC.

Note

Online insertion and removal (OIR) is not supported on the Port Adapter Jacket Card. OIR is supported
on the port adapter. You must have the chassis powered off to install or remove the Port Adapter Jacket
Card.

1

Printed circuit board

2

Metal carrier

H6419

1

2

«
...
28
29
30
31
32
...
»

Summary of Contents for PA-MC-2T3-EC=

































































































Reviews:

No comments

Related manuals for PA-MC-2T3-EC=

Brand: SWEEX Pages: 3

Brand: Nextech Pages: 7

Brand: Harman Kardon Pages: 8

Brand: AMEC Pages: 4

Brand: Planet Pages: 2

Brand: Lindy Pages: 2

Thunderbolt MTB3-002-HD

Brand: Tripp Lite Pages: 31

UltraAV DisplayPort

Brand: Accell Pages: 2

Brand: StarTech.com Pages: 9

Brand: Lindy Pages: 16

Brand: SMC Networks Pages: 2

WiShare SMCWTVA100

Brand: SMC Networks Pages: 81

EZ Connect SMCWUSBS-N3

Brand: SMC Networks Pages: 2

EZ Connect SMCWUSB-G

Brand: SMC Networks Pages: 54

EZ Connect SMC2435W

Brand: SMC Networks Pages: 2

Brand: SMC Networks Pages: 44

10GPCIE-10BT FICHE

Brand: SMC Networks Pages: 2

Brand: Gogen Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands