Cisco PA-MC-2T3-EC= Installation And Configuration Manual Download

Page: 55 / 96

4-17

PA-MC-T3-EC Port Adapter Installation and Configuration

OL-10589-02

Chapter 4 Configuring the Unchannelized Mode

Checking the Configuration

Using the show version or show hardware Commands

Display the configuration of the system hardware, the number of each interface type installed, the Cisco
IOS software version, the names and sources of configuration files, and the boot images, using the

show

version

(or

show hardware

) command. Following is an examples of the

show version

command.

Note

The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.

Following is an example of the

show version

command from a Cisco 7200 VXR router with the

PA-MC-T3-EC:

Router#

show version

Cisco IOS Software, 7200 Software (C7200-JS-M), Experimental Version 12.4(20060505:140248)

[sprafull-CJ-G2 102]

Compiled Fri 05-May-06 20:21 by

ROM: System Bootstrap, Version 12.4(4r)XD3, RELEASE SOFTWARE (fc1)

reg2 uptime is 14 hours, 35 minutes

System returned to ROM by reload at 07:19:23 UTC Sun Jan 16 2000

System image file is "disk2:c7200p-js-mz.CJ_DTHO_20060505"

Last reload reason: Reload Command

Cisco 7206VXR (NPE-G2) processor (revision B) with 917504K/65536K bytes of memory.

Processor board ID 34149641

MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.1

6 slot VXR midplane, Version 2.9

Last reset from power-on

PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.

Current configuration on bus mb1 has a total of 660 bandwidth points.

The set of PA-2FE, PA-POS-2OC3, and I/O-2FE qualify for "half

bandwidth points" consideration, when full bandwidth point counting

results in oversubscription, under the condition that only one of the

two ports is used. With this adjustment, current configuration on bus

mb1 has a total of 660 bandwidth points.

This configuration has oversubscripted the PCI bus and is not a

supported configuration.

PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.

Current configuration on bus mb2 has a total of 960 bandwidth points.

The set of PA-2FE, PA-POS-2OC3, and I/O-2FE qualify for "half

bandwidth points" consideration, when full bandwidth point counting

results in oversubscription, under the condition that only one of the

two ports is used. With this adjustment, current configuration on bus

mb2 has a total of 660 bandwidth points.

This configuration has oversubscripted the PCI bus and is not a

supported configuration.

Please refer to the following document "Cisco 7200 Series Port Adaptor

Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>

for c7200 bandwidth points oversubscription and usage guidelines.

WARNING: PCI bus mb1 Exceeds 600 bandwidth points

WARNING: PCI bus mb2 Exceeds 600 bandwidth points

Summary of Contents for PA-MC-2T3-EC=

































































































Search results

Summary of Contents for PA-MC-2T3-EC=

Reviews:

Related manuals for PA-MC-2T3-EC=

Brands by name

Popular brands

Cisco PA-MC-2T3-EC=, Installation And Configuration Manual

Search results

Summary of Contents for PA-MC-2T3-EC=

Reviews:

Related manuals for PA-MC-2T3-EC=

Brands by name

Popular brands