manualshive.com logo in svg

Cisco CCNA 2, Instructor Manual

Get your hands on the Cisco CCNA 2 Instructor Manual, a comprehensive and essential resource for networking professionals. This manual can be downloaded for free from our website, offering detailed instructions and guidance to enhance your understanding of Cisco CCNA 2.

Share
Download
background image

55 - 238

 

CCNA 2: Routers and Routing Basics v3.1 Instructor Guide – Module 5 

Copyright 

©

 2004, Cisco Systems, Inc.  

5.2.1 IOS file system overview 

A router or switch requires software to operate. The following are two basic types of essential 
software: 

• 

The operating system 

• 

The config file 

The operating system that is used in almost all Cisco devices is the Cisco IOS. The IOS is the 
software that allows the hardware to function as a router or a switch. The software a router or 
switch uses is referred to as the configuration, or config file. The configuration file contains the 
instructions that define how the device will route or switch. 

The IOS is stored in Flash memory. The configuration file is stored in NVRAM. Discuss with 
the students the differences between these types of memory and help the student understand 
by opening a router and showing the inside of the router to the students. Discuss RAM, ROM, 
flash, and NVRAM. Students must understand the differences between them. One difference 
to discuss is that the IOS in flash or RAM is several megabytes and the configuration file in 
NVRAM is up to a few kilobytes. 

Version 12 and newer releases of the IOS provide a single interface to all file systems. This is 
referred to as the Cisco IOS File System (IFS). The IFS can be used to perform all the file 
system management for a router. Explain that the IFS is based on UNIX file systems.  

5.2.2 IOS naming convention 

Many different versions of the IOS are available. The IOS supports many different hardware 
platforms and features. This is a continuous development process.  

To identify the different versions, Cisco has a naming convention for the IOS files. The IOS 
naming convention uses different fields in the name such as hardware platform identification, 
feature set identification, and the numerical release. 

The first part of the IOS filename identifies the hardware platform. The second part of the IOS 
filename identifies the various features that the file contains. The third part of the filename 
indicates the file format. It specifies if the IOS is stored in flash, if it is in compressed format, 
and if it can be released. The fourth part of the filename identifies the IOS release. 

This is an important concept for students to understand. They should be able to look at an IOS 
filename and determine the hardware platform, features, file format, and the release. Students 
should also understand that these naming conventions vary for different releases. This occurs 
as the feature sets are rebundled and renamed.  

Show students some of the tools for IOS planning that are available on the Cisco website. 
Most of these are only available to users who have obtained user ids through SmartNet.  

http://www.cisco.com/warp/customer/620/1.html

 

http://www.cisco.com/en/US/customer/products/sw/iosswrel/ios_abcs_ios_networking_the_ent
erprise0900aecd800a4e14.html

 

Summary of Contents for CCNA 2
















































































































































































































































Reviews:

No comments

Related manuals for CCNA 2

PaloAlto Networks ION 1200 Series Hardware Reference Manual preview
ION 1200 Series
Brand: PaloAlto Networks Pages: 90
Lancom 7100 VPN Manual preview
7100 VPN
Brand: Lancom Pages: 70
Patton electronics SMARTNODE 4950 Quick Start Manual preview
SMARTNODE 4950
Brand: Patton electronics Pages: 12
Patton electronics 1000RC User Manual preview
1000RC
Brand: Patton electronics Pages: 9
Qlogic QLE7xxx Series Quick Start Manual preview
QLE7xxx Series
Brand: Qlogic Pages: 8
Gira 0535 00 Installation Instructions Manual preview
0535 00
Brand: Gira Pages: 6
Patton electronics SmartNode 4520 Series Getting Started Manual preview
SmartNode 4520 Series
Brand: Patton electronics Pages: 90
B&B Electronics EIP308 Product Information preview
EIP308
Brand: B&B Electronics Pages: 2
ATEN Slideaway CL1008 User Manual preview
Slideaway CL1008
Brand: ATEN Pages: 77
Variscite VAR-EXT-CB103 Manual preview
VAR-EXT-CB103
Brand: Variscite Pages: 17
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual preview
Acme Packet 3900
Brand: Oracle Pages: 70
Multi-Link Power Stone Programming Manual preview
Power Stone
Brand: Multi-Link Pages: 31
MicroNova O047 Technical Installation Manual preview
O047
Brand: MicroNova Pages: 113
BinTec BinGO! DSL II Quick Install Manual preview
BinGO! DSL II
Brand: BinTec Pages: 2
SMC Networks SMCGS10P-Smart Installation Manual preview
SMCGS10P-Smart
Brand: SMC Networks Pages: 68
Digital Watchdog Compressor DW-CP04 User Manual preview
Compressor DW-CP04
Brand: Digital Watchdog Pages: 73
ratiotec CONNECT Box Pro Instruction Manual preview
CONNECT Box Pro
Brand: ratiotec Pages: 12
IOGear GEU302 Quick Start Manual preview
GEU302
Brand: IOGear Pages: 8

Brands by name

Popular brands

Load more brands