Cisco CableCARD Staging Manual Download Page 117

Page: 117 / 184

PowerKEY/EA Issues

734375 Rev H

107

Symptom

Diagnostic
Screen

Type of
DHCT

Possible Solution

ISE errors
continually
increment
when an
instant hit is
sent to the
DHCT from
the billing
system or
from the
DNCS

Page 6

Unstaged

Do the MAC addresses and Secure Micro for the DHCT
match what is recorded in the DNCS?

–

yes

, follow these steps:

Ask the DNCS operator to perform a

modDhctCfg -s

on the DHCT.

Stage the DHCT again.

–

, continue with step 2.

Follow these steps:

Delete the DHCT from the DNCS.

Try to stage the DHCT again using the new EMMs.

If these steps do not work, return the DHCT to us for repair.
Mark the repair tag with

S1. No EMMs/ISE/EA.

Summary of Contents for CableCARD

























































































































































































Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands

Cisco CableCARD, Staging Manual

Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands