Cisco CableCARD Staging Manual Download Page 6

Page: 6 / 184

Contents

734375 Rev H

Copy the EMM File ................................................................................................................ 58

Send the EMM File to the DNCS Using FTP ...................................................................... 59

Extract the EMM File ............................................................................................................. 60

Copy the TOC File ................................................................................................................. 61

Load EMM Data ..................................................................................................................... 62

How to Stage DHCTs

Overview ................................................................................................................................. 68

DHCT Staging Flowchart ..................................................................................................... 69

Staging DHCTs with Services .............................................................................................. 70

Staging DHCTs For Instastaging ......................................................................................... 71

Verify the PowerKEY Information ...................................................................................... 72

Verifying the Staging Process .............................................................................................. 75

How to Stage CableCARD Modules

Overview ................................................................................................................................. 78

Setting Up the DNCS for CableCARD Module Staging ................................................... 79

Staging CableCARD Modules .............................................................................................. 80

Verify CableCARD Module Staging ................................................................................... 85

Returning DHCTs and CableCARD Modules to Service

Check for Stranded IPPV Events and Clear NVM ............................................................ 88

Returning CableCARD Modules to Service ....................................................................... 92

Troubleshooting

Staging Failures ...................................................................................................................... 94

DHCT Errors ........................................................................................................................... 95

Send Instant Hits .................................................................................................................... 99

OS and ResApp Downloads ............................................................................................... 101

PowerKEY/EA Issues ......................................................................................................... 104

Customer Information

109

Appendix A Download LED Indicators

111

Overview ............................................................................................................................... 112

LED Indicators Displayed During an OSM Download .................................................. 113

LED Indicators Displayed During a CVT Download ..................................................... 116

DHCTs with Three LED Indicators ................................................................................... 119

DHCTs with Single LED Indicators .................................................................................. 122

POWER LED Indicators Displayed on DHCTs ............................................................... 125

Summary of Contents for CableCARD

























































































































































































Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands

Cisco CableCARD, Staging Manual

Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands