Cisco CableCARD Staging Manual Download Page 124

Page: 124 / 184

Appendix A

Download LED Indicators

114

734375 Rev H

Stage Alphanumeric

LED Indicator

TV Monitor

Description

and then

CLr

appears when the current OS image

clears.

Pr.00

appears when the new

received image overwrites it the current
OS image.

The rotating border appears when the
DHCT boots into the OS.

Dancing dashes appear when Guardian
downloads the second part of the image,
which contains the ResApp, from BFS to
internal DRAM.

The wave indicates that the DHCT resets to
execute programming.

and then

CLr and PR.00 indicate that the second
part of the OS is installed into flash
memory.

Programs upper memory area with
ResApp.

The wave appears after the DHCT resets to
boot into the OS and the newly
downloaded ResApp.

10.

The rotating border appears when the
DHCT resets and boots into the OS.

11.

The LED is clear when the OS has started
the ResApp. The DHCT is in an Off state.

Summary of Contents for CableCARD

























































































































































































Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands

Cisco CableCARD, Staging Manual

Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands