Cisco CableCARD Staging Manual Download Page 40

Page: 40 / 184

Chapter 3 Optimize Your System Performance for Downloads and Staging

734375 Rev H

Running the listOSM Utility and Removing Unneeded Files

The listOSM utility determines which DHCT models are currently using the OSM
download method and reports the unused files in the OS list.

Running the listOSM Utility and Removing Unneeded Files

Are you using the OSM download method for any DHCTs in your network?



yes

or if you are

unsure

, go to step 2.



, go to

Running the listCVT Utility and Removing Unneeded Files

(on

page 31).

Open an xterm window on the DNCS.

Type

listOSM -v

and press

Enter

. This command provides you the version of

listOSM utility that is currently on your network.

Compare the version number of the listOSM utility on your DNCS with the
version number listed in the ROM to Model Matrix in the

Downloading New

Client Application Platform Installation Instructions

(part number 4003052).



If the version number is equal to or greater than the one listed in the matrix,
go to step 5.



If the version number is less than the one listed in the matrix, contact Cisco
Services to receive the latest utility.

Type one of the following, based on the system release you have installed:



For SR 4.2.1 and earlier, type

cd /export/home/dncs/doctor

and press

Enter



For SR 4.3 and later, type

cd /dvs/dncs/Utilities/doctor

and press

Enter

Note:

Be sure to type a space between

and

Result:

The current directory is now the doctor directory.

Type

listOSM > preosm

and press

Enter

Type

more preosm

and press

Enter

. This command lets you view the file and

verify the current download configuration for each DHCT type active in the
network.

Does the report indicate that there are unused files?



yes

, go to step 9.



, go to

Running the listCVT Utility and Removing Unneeded Files

(on

page 31).

On the DNCS Administrative Console, select the

DNCS

tab and then select one

of the following tabs based on the system release you have installed:



For SR 2.5/3.5/4.0 and earlier, select the

Element Provisioning

tab.



For SR 2.7/3.7/4.2 and later, select the

Home Element Provisioning

tab.

Click

. The DHCT OS List window opens.

Summary of Contents for CableCARD

























































































































































































Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands

Cisco CableCARD, Staging Manual

Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands