Circutor SVGm-3WF-100C-480 Instruction Manual Download Page 71

Page: 71 / 102

Instruction Manual

SVGm

9.- ETHERNET COMMUNICATIONS

For an installation with devices in parallel, the Ethernet connection can be made on any device.

9�1�- CONNECTION

The

SVGm

has an Ethernet port. This type of communication creates an intranet with IP communica-

tions.

If the device that connects to this port is a computer, the network cable must be a crossover Ethernet

cable, as shown in

Figure 72

Figure 72:RJ-45 connector: Crossover Ethernet connection diagram�

9�2�- WEB SITE

The device has a web site for viewing and configuring the parameters.

Figure 73

shows the main web server screen, from where you can access all of the information of the

SVGm

Figure 73: Main screen of the web site�

Summary of Contents for SVGm-3WF-100C-480







































































































Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands

Circutor SVGm-3WF-100C-480, Instruction Manual

Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands