Circutor SVGm-3WF-100C-480 Instruction Manual Download Page 44

Page: 44 / 102

SVGm

Instruction Manual

6.- DISPLAY

6�1�- MAIN SCREEN

6�1�1� - DEVICE SINGLE OR MASTER

Figure 40

shows the main screen of a

“single”

“master”

device.

Arrancando ...

RUN / STOP key

RESET key

Main

% of power

Active Power

Reactive Power

Cos

Status messages

Active Power

Reactive Power
Cos

Load

Figure 40: Main screen�

It shows the

Cos

Active

and

Reactive Power

values in the Main and in the Load. And the

% of SVG

power

used.

The

key allows you to restart the device if an alarm has been generated and this has been

resolved.

The

key is the start and stop key of the

SVGm

Use the

and

keys to navigate through the different display screens.

In the upper part of the screen, a message with the current status of the device is shown (

Table 21

Table 21: Status messages

Status messages

Starting

Description

The

SVGm

is starting up.

Init

Description

The device is starting the systems.

Waiting comms

Description

Initiating internal communication systems

Waiting for conditions

Description

Waiting for the conditions to be met in order to operate.

Summary of Contents for SVGm-3WF-100C-480







































































































Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands

Circutor SVGm-3WF-100C-480, Instruction Manual

Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands