Circutor SVGm-3WF-100C-480 Instruction Manual Download Page 59

Page: 59 / 102

Instruction Manual

SVGm

7�4�- OPERATING LIMITS

Note:

This screen is not visible on the

“slave”

devices.

In this screen,

Figure 62

, the operating limits of the device are configured:

Figure 62: Configuration screen: Operating limits�

●

Min current

The minimum load current to start the static generator is configured with this parameter. Minimum

current feature is used to increase the system efficiency, by stopping the static generator when re-

quired. The

SVGm

will stop when the load current is below the entered value and will start when it is

higher.

Range of values:

Minimum value:

0 A

Maximum value:

5000 A

●

Current limit

This parameter allows the maximum power of the static generator to be limited. The value is config-

ured as a percentage with respect to the device’s rated power.

Range of values:

Minimum value:

20%

Maximum value:

100%

Press the

key to access the next configuration step

Press the

key to access the main screen of the device without saving the configuration values.

Summary of Contents for SVGm-3WF-100C-480







































































































Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands

Circutor SVGm-3WF-100C-480, Instruction Manual

Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands