Circutor SVGm-3WF-100C-480 Instruction Manual Download Page 51

Page: 51 / 102

Instruction Manual

SVGm

Figure 49: Confirm screen�

This screen,

Figure 50

, shows the active warnings.

Table 23

shows the warnings that can appear on the

device’s display.

Figure 50: Warnings�

Use the

and

keys to navigate through the different display screens.

Table 23: Warnings messages�

Warnings messages

Waiting for conditions

Description

The start-up conditions are not met.

Corrective

action

Check the alert messages.

Load polarity

Description

Detection of an error in the load polarity.

Corrective

action

Check the transformer connections. See section

“7.6.- TRANSFORMER CONFIGURATION”

Annual maintenance

Description

A year has passed since the last maintenance procedure was carried out and the maintenance meter

was reset.

Corrective

action

Perform the annual maintenance procedure and reset the maintenance meter. (see

“10.- MAINTE-

NANCE”

)

Fan maintenance

Description

Fans have been operating for over 40,000 hours; they must be replaced and the maintenance meter

must be reset.

Summary of Contents for SVGm-3WF-100C-480







































































































Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands

Circutor SVGm-3WF-100C-480, Instruction Manual

Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands