Circutor SVGm-3WF-100C-480 Instruction Manual Download Page 66

Page: 66 / 102

SVGm

Instruction Manual

8.- RS-485 COMMUNICATIONS

SVGm

devices have an RS-485 serial communication output with the

MODBUS RTU

® communica-

tions protocol.

For an installation with devices in parallel, the RS-485 connection can be made on any device.

8�1�- CONNECTIONS

The RS-485 cable must be wired with twisted pair cable with mesh shield (minimum 3 wires), with a

maximum distance between the

SVGm

and the master device of 1200 metres.

A maximum of

SVGm

static generators can be connected to this bus.

To establish communications with the master device, use an RS-485 intelligent converter.

B(-)

A(+)

RS-232 / USB / Ethernet / Profibus ...

RS-485

RS-232

USB

Ethernet

Profibus

...

A B

Figure 71: RS-485 Connection diagram�

The RS-485 communications configuration in

SVGm

models is set to a baud rate of 9600 bps, 8 data

bits, 1 stop bit and no parity.

Summary of Contents for SVGm-3WF-100C-480







































































































Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands

Circutor SVGm-3WF-100C-480, Instruction Manual

Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands