Circutor SVGm-3WF-100C-480 Instruction Manual Download Page 39

Page: 39 / 102

Instruction Manual

SVGm

be used in distorted networks, with no need to add filtering elements to the installation.

4�2�- MEDIUM VOLTAGE

The

SVGm

is able to compensate for the reactive current in medium voltage with the unit connected

in low voltage. To do this, a current measurement transformer must be used to measure the medium

voltage current.

There is a phase difference in the currents in the primary and secondary transformer coils that de-

pends on the construction of the transformer. To compensate for this difference, the type of transform-

er used and its transformation ratio has to be entered in the settings screen (

“7.7 - MEDIUM VOLTAGE”

This information is available on the transformer’s rating plate.

Medium Voltage

Low Voltage

Figure 34: Operation of the SVGm in Medium Voltage�

4�3�- SELF-DIAGNOSIS

The device is fitted with a self-diagnosis system. The device checks the integrity of the hardware and

software control elements when starting up. This analysis is carried out according to

IEC60730

This system ensures the device remains in a safe state in the event of failure. The user is alerted to the

failure thanks to an on-screen message and it is also found in the Modbus register.

This type of failure indicates damage or degradation of any of the control and process elements, both

hardware and software. Turning off the device and contacting

TAS

is recommended whenever this

alarm comes about.

4�4�- THERMAL PROTECTION

The device features several levels of thermal protection:



Ventilation regulation

, the fan speed is adjusted as needed at any given time, thus minimising the

noise in the device.



Static temperature limitation,

the device reduces its power if the internal temperature exceeds

certain limits. This maximises the availability of the device in any situation.



Dynamic limitation of the device,

one of the factors affecting the reliability of the device is the

stress caused by repeated heating and cooling cycles. The device adjusts both its ventilation and power

to minimise the impact that thermal cycling has on the life of the device.

Summary of Contents for SVGm-3WF-100C-480







































































































Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands

Circutor SVGm-3WF-100C-480, Instruction Manual

Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands