Circutor SVGm-3WF-100C-480 Instruction Manual Download Page 21

Page: 21 / 102

Instruction Manual

SVGm

The use of transformers with ratios close to the current to be measured is recommend-

ed.

The correct connection of the current transformers is vital for the

SVGm

static genera-

tors to operate properly. If the phases L1, L2 and L3 are switched in the secondary, the

static generator will not work properly.

The

SVGm

devices have built-in fuse overcurrent protection.

Install external protection according to the type of installation, the facility’s maximum

short-circuit current, the maximum fuse current, and the regulations in force at the

place of installation.

If local regulations require the use of earth leakage protection devices, only DC sensitive

RCD (RCD type B) should be used with

SVGm

. Static generators work internally with DC

currents, and, in case of failure, the DC currents may produce malfunction on type A

RCD devices.

Ensure that the installation of the device in your electric distribution system (TN, VT, IT)

complies with current standards.

Check that there is a neutral in the place where three-phase static generator connections are made

with neutral,

SVGm-4WF-xxxx

Do not install various static generators in series one after another in the same instal-

lation, configured to correct the same disturbances. This can produce an overcompen-

sation of the disturbances, which could cause instability in the mains (

Figure 7

)

Figure 7: Do not install various static generators in series�

Summary of Contents for SVGm-3WF-100C-480







































































































Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands

Circutor SVGm-3WF-100C-480, Instruction Manual

Search results

Summary of Contents for SVGm-3WF-100C-480

Reviews:

Related manuals for SVGm-3WF-100C-480

Brands by name

Popular brands