manualshive.com logo in svg

Chrysler 2017 Pacifica, Owner'S Manual, Page: 640 / 828

Share
Download
Chrysler 2017 Pacifica Owner'S Manual Download Page 640

fluid specifications. It is important to maintain the trans-
mission fluid at the correct level using the recommended
fluid.

NOTE:

No chemical flushes should be used in any

transmission; only the approved lubricant should be
used.

CAUTION!

Using a transmission fluid other than the manufac-
turer’s recommended fluid may cause deterioration
in transmission shift quality and/or torque converter
shudder. Refer to “Fluids And Lubricants” in “Tech-
nical Data” for fluid specifications.

Special Additives

The manufacturer strongly recommends against using
any special additives in the transmission. Automatic
Transmission Fluid (ATF) is an engineered product and

its performance may be impaired by supplemental addi-
tives. Therefore, do not add any fluid additives to the
transmission. Avoid using transmission sealers as they
may adversely affect seals.

CAUTION!

Do not use chemical flushes in your transmission as
the chemicals can damage your transmission compo-
nents. Such damage is not covered by the New
Vehicle Limited Warranty.

Fluid Level Check

The fluid level is preset at the factory and does not
require adjustment under normal operating conditions.
Routine fluid level checks are not required, therefore the
transmission has no dipstick. Your authorized dealer can
check your transmission fluid level using special service

638

MAINTAINING AND CARING FOR YOUR VEHICLE

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments