manualshive.com logo in svg

Chrysler 2017 Pacifica, Owner'S Manual, Page: 593 / 828

Share
Download
Chrysler 2017 Pacifica Owner'S Manual Download Page 593

If the tire inflates to the recommended pressure or is at
least 26 psi (1.8 Bar) pressure within 15 minutes:

NOTE:

If the tire becomes over-inflated, push the Defla-

tion Button to reduce the tire pressure to the recom-
mended inflation pressure before continuing.

1. Push the Power Button to turn off

the Tire Service Kit.

2. Remove the speed limit label from

the Tire Service Kit and place
sticker on the steering wheel.

3. Immediately disconnect the Sealant Hose from the

valve stem, reinstall the cap on the fitting at the end of
the hose, and place the Tire Service Kit in the vehicle
storage location. Proceed to “Drive Vehicle.”

7

IN CASE OF EMERGENCY

591

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments