Home
/
Chrysler
/
2017 Pacifica
/
Owner'S Manual

Chrysler 2017 Pacifica, Owner'S Manual, Page: 164 / 828

Share

Page: 164 / 828

Chrysler 2017 Pacifica Owner'S Manual Download Page 164

NOTE:

If “Unlock All Doors 1st Press”’ is programmed

in Uconnect Settings, all doors will unlock with a Passive
Entry handle activation. If ‘Unlock Driver Door 1st Press”
is programmed in Uconnect Settings, only the liftgate
will unlock. Refer to “Uconnect Settings” in “Multime-
dia” for further information.

Closing

To Close The Vehicle

Grasp the liftgate closing handle and initiate lowering the
liftgate. Release the handle when the liftgate takes over
the closing effort.

The liftgate can also be closed using the Rear Power
Liftgate button (If Equipped), located in the upper left
trim in the liftgate opening. Pushing button will only
close the liftgate. This button cannot be used to open the
liftgate.

To Lock The Vehicle

With a valid Passive Entry RKE Key Fob within 3 ft (1 m)
of the liftgate, pushing the passive entry lock button
located to the right of the outside handle will lock the
vehicle.

Rear Power Liftgate Switch

162

GETTING TO KNOW YOUR VEHICLE

«
...
162
163
164
165
166
...
»

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments