manualshive.com logo in svg

Chrysler 2017 Pacifica, Owner'S Manual, Page: 216 / 828

Share
Download
Chrysler 2017 Pacifica Owner'S Manual Download Page 216

Instrument Cluster Descriptions

For 3.5” EVIC Cluster and 7” DID Cluster

1. Tachometer

•

Indicates the engine speed in revolutions per minute
(RPM x 1000).

2. 3.5” EVIC / 7” DID Information Display

•

When the appropriate conditions exist, this display
shows the 3.5” EVIC OR 7” DID messages. Refer to
“Display” located in “Getting To Know Your Instru-
ment Panel” for further information.

3. Speedometer

•

Indicates vehicle speed.

4. Fuel Gauge

•

The gauge shows the level of fuel in the fuel tank
when the ignition switch is in the ON/RUN position.

•

The fuel pump symbol points to the side of the

vehicle where the fuel door is located.

5. Temperature Gauge

•

The temperature gauge shows engine coolant tem-
perature. Any reading within the normal range indi-
cates that the engine cooling system is operating
satisfactorily.

•

The gauge can indicate a higher temperature when
driving in hot weather or up mountain grades. It
should not be allowed to exceed the upper limits of
the normal operating range.

WARNING!

Driving with a hot engine cooling system could
damage your vehicle. If the temperature gauge
reaches “H” pull over and stop the vehicle. Idle the
vehicle with the air conditioner turned off until the

(Continued)

214

GETTING TO KNOW YOUR INSTRUMENT PANEL

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments