manualshive.com logo in svg

Chrysler 2017 Pacifica, Owner'S Manual, Page: 566 / 828

Share
Download
Chrysler 2017 Pacifica Owner'S Manual Download Page 566

1. Loosen (but do not remove) the wheel lug nuts by

turning them to the left one turn while the wheel is
still on the ground.

2. There are two jack engagement locations on each side

of the vehicle body. These locations are on the sill
flange of the vehicle body.

CAUTION!

Do not attempt to raise the vehicle by jacking on
locations other than those indicated.

Extending The Wrench

Jack Locations

564

IN CASE OF EMERGENCY

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments