manualshive.com logo in svg

Chrysler 2017 Pacifica, Owner'S Manual, Page: 608 / 828

Share
Download
Chrysler 2017 Pacifica Owner'S Manual Download Page 608

•

Vehicles with a discharged battery or total electrical
failure when the electric parking brake (EPB) is en-
gaged, will need a wheel dolly or jack to raise the rear
wheels off the ground when moving the vehicle onto a
flatbed.

The manufacturer recommends towing your vehicle with
all four wheels

OFF

the ground using a flatbed.

If flatbed equipment is not available, this vehicle must
towed with the front wheels OFF the ground (using a
towing dolly, or wheel lift equipment with the front
wheels raised).

NOTE:

Ensure that the Electric Park Brake is released,

and remains released, while being towed.

CAUTION!

Towing this vehicle in violation of the above require-
ments can cause severe transmission damage. Dam-
age from improper towing is not covered under the
New Vehicle Limited Warranty.

Vehicle Recovery Tow Points

Your vehicle is equipped with Vehicle Recovery Points
that can be used to recover a disabled vehicle, located on
the underbody of the vehicle.

NOTE:

•

Ensure that the towing service tow hooks are properly
seated and secured in the attachment points.

•

This recovery tow feature should be used by a trained
professional only.

606

IN CASE OF EMERGENCY

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments