Home
/
Chrysler
/
2017 Pacifica
/
Owner'S Manual

Chrysler 2017 Pacifica, Owner'S Manual, Page: 526 / 828

Share

Page: 526 / 828

Chrysler 2017 Pacifica Owner'S Manual Download Page 526

2. Slow down if the road has standing water or puddles.

3. Replace the tires when tread wear indicators first

become visible.

4. Keep tires properly inflated.

5. Maintain sufficient distance between your vehicle and

the vehicle in front of you to avoid a collision in a
sudden stop.

Driving Through Water

Driving through water more than a few inches/
centimeters deep will require extra caution to ensure
safety and prevent damage to your vehicle.

Flowing/Rising Water

WARNING!

Do not drive on or across a road or path where water
is flowing and/or rising (as in storm run-off). Flow-
ing water can wear away the road or path’s surface
and cause your vehicle to sink into deeper water.
Furthermore, flowing and/or rising water can carry
your vehicle away swiftly. Failure to follow this
warning may result in injuries that are serious or
fatal to you, your passengers, and others around you.

524

STARTING AND OPERATING

«
...
524
525
526
527
528
...
»

Summary of Contents for 2017 Pacifica





























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments